Sheep Health & Management

The Curved Panel is required for the Starter Sheep Handling System. The Curved Panel can be joined to other sheeted or open rail panels and gates ...

The Trombone Sheep System is made with a hot dipped galvanized finish. The sides can be adjusted for width and the joining pins are long enough tha...

The Ritchie Guillotine Gate gives you fast effective control and movement. Opening and closing the gate can be accomplished remotely due to the lon...

The Lift and Slide Gate is a less stressful way to move sheep and goats.  Instead of swinging the gate back against the oncoming flow of sheep or g...

The Aluminum Sheep Panel is manufactured in lightweight, heat treated aluminum for increased rigidity. These robust panels are great for a race as ...

The Curved Inner Panel is required for the Trombone System. The Joining Link Bracket is needed to attach the Curved Inner Panel to an open rail or ...

The Ritchie Swing Gates in Frame are easy to open and close with one hand which makes life so much easier when getting in and out of pens. These ga...

The Ritchie Open Rail Sheep Panels are used mainly in penning and come in 3 different lengths. They can be pinned together with the Joining Pin. T...

The Ritchie Lamb Creep Panel is robustly constructed with tubular steel frame.  The spacing is easily adjusted between the rollers. You steel rolle...

The Joining Pin Link Bracket is required for the Trombone Systems. The Joining Link Bracket is needed to attach the Curved Inner Panel to an open r...

Ritchie Sheep Panel posts for building in or bolting down. They are hot dipped galvanized finish.

The Ritchie Cap and Socket is a 178 mm square ground socket with a steep cap to close of when not in use. It is designed to take 50mm x 50mm square...

The Remote Control Lever for the Draft/Stop Sheep Gate gives you the ability to run the sorting sheep gate from a distance.

The Te Pari LPG Calf Dehorner comes standard with the 18 mm dehorning tips. Sizes 14mm, 16mm, 18mm, and 20mm tips can be purchased as spares.   

QUICK, EFFECTIVE AND EFFICIENT. The Te Pari LPG Calf Dehorner is a NZ-made, fully portable LPG gas fired unit that will constantly maintain a high ...

The Portable Starter Sheep System is made with a hot dipped galvanized finish. The sides can be adjusted for width and the joining pins are long en...

JUG Waterers are an energy efficient way to provide clean fresh water to your livestock. The earth tubes help give you that geo-thermal heat for m...

Tru-Test Weigh Platform Low profile design No sharp edges Rubber mat secured to platform with aluminium plates on each end 1/2" rubber mat for tra...

The SRS2 EID Stick Reader makes scanning easy.  Quickly read, record and transfer your livestock EID Tag information with the durable, easy to use ...

Increase the rate of gain on your young stock with the HEATWAVE cost effective milk feeding system that is easy to clean! The HEATWAVE MILK WARM...

The Heatwave Milk Machine comes with 4 lamb nipples but these extra lamb teats can be purchased as needed. Although these look very similar and can...

The Teatguard has been developed to help extend the life of lamb nipples. They help prevent bullying, protect the teats and encourage a good suckin...

One box of cleaning tablets should last for about 6 weeks of cleaning your Heatwave Milk Warmer.   This product has been tested with the Heatwave t...

The starter teats can help get young lambs and goat kids adjust more quickly to the Heatwave Milk Machine. The Heatwave comes with 4 regular lamb n...

The Heatwave Milk Warmer comes with 4 calf teats. Extras can be purchased so you don't need to worry about running out.

The Bubble pump will allow you to clean the pipes and prime the system easily, quickly and without disconnecting pipes.  Two Bubble Pumps come stan...

The picture shows a role of 5 meters of silicone tubing. The price is $5.40 per meter.  Silicone Tubing for 4 nipples comes standard with the purch...

  The Bulkhead Push-Fit Assembly helps to attach the silicone tube to the Heatwave Milk Warmer.   

The Straight Barbed Pipe Connector connects the silicone tube at a point where the pump can be connected. It is always great to have some of these ...

 The Collet is Part of the Heatwave Bulkhead Push fit Assembly 8mm which helps to attach the silicone tube to the Heatwave Milk Warmer.   

 The Non-Return Valve is a key component in the Heatwave Milk Warmer as it helps prevent milk from dripping out of the teats as well as keeping mil...

 The Heatwave Exchange Coil is a key component in the Heatwave Milk Warmer as it is needed to warm the milk for the youngstock. It is important to ...

 The Barrel Tap doesn't automatically come with the purchase of the Heatwave Milk Warmer but is  recommended if using a barrel for feeding calves. ...

 The 6mm Y Connector is used for connecting silicone tubes for the Heatwave Milk Warmer.

 The Plastic Push-in Connector is used for connecting the silicone tubes to other components in  the Heatwave Milk Warmer.